In the Linux kernel, the following vulnerability has been resolved:
x86/fpu: Clear XSTATE_BV[i] in guest XSAVE state whenever XFD[i]=1
When loading guest XSAVE state via KVM_SET_XSAVE, and when updating XFD in
response to a guest WRMSR, clear XFD-disabled features in the saved (or to
be restored) XSTATE_BV to ensure KVM doesn't attempt to load state for
features that are disabled via the guest's XFD. Because the kernel
executes XRSTOR with the guest's XFD, saving XSTATE_BV[i]=1 with XFD[i]=1
will cause XRSTOR to #NM and panic the kernel.
E.g. if fpu_update_guest_xfd() sets XFD without clearing XSTATE_BV:
------------[ cut here ]------------
WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#29: amx_test/848
Modules linked in: kvm_intel kvm irqbypass
CPU: 29 UID: 1000 PID: 848 Comm: amx_test Not tainted 6.19.0-rc2-ffa07f7fd437-x86_amx_nm_xfd_non_init-vm #171 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:exc_device_not_available+0x101/0x110
Call Trace:
<TASK>
asm_exc_device_not_available+0x1a/0x20
RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
switch_fpu_return+0x4a/0xb0
kvm_arch_vcpu_ioctl_run+0x1245/0x1e40 [kvm]
kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
__x64_sys_ioctl+0x8f/0xd0
do_syscall_64+0x62/0x940
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
This can happen if the guest executes WRMSR(MSR_IA32_XFD) to set XFD[18] = 1,
and a host IRQ triggers kernel_fpu_begin() prior to the vmexit handler's
call to fpu_update_guest_xfd().
and if userspace stuffs XSTATE_BV[i]=1 via KVM_SET_XSAVE:
------------[ cut here ]------------
WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#14: amx_test/867
Modules linked in: kvm_intel kvm irqbypass
CPU: 14 UID: 1000 PID: 867 Comm: amx_test Not tainted 6.19.0-rc2-2dace9faccd6-x86_amx_nm_xfd_non_init-vm #168 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:exc_device_not_available+0x101/0x110
Call Trace:
<TASK>
asm_exc_device_not_available+0x1a/0x20
RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
fpu_swap_kvm_fpstate+0x6b/0x120
kvm_load_guest_fpu+0x30/0x80 [kvm]
kvm_arch_vcpu_ioctl_run+0x85/0x1e40 [kvm]
kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
__x64_sys_ioctl+0x8f/0xd0
do_syscall_64+0x62/0x940
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
The new behavior is consistent with the AMX architecture. Per Intel's SDM,
XSAVE saves XSTATE_BV as '0' for components that are disabled via XFD
(and non-compacted XSAVE saves the initial configuration of the state
component):
If XSAVE, XSAVEC, XSAVEOPT, or XSAVES is saving the state component i,
the instruction does not generate #NM when XCR0[i] = IA32_XFD[i] = 1;
instead, it operates as if XINUSE[i] = 0 (and the state component was
in its initial state): it saves bit i of XSTATE_BV field of the XSAVE
header as 0; in addition, XSAVE saves the initial configuration of the
state component (the other instructions do not save state component i).
Alternatively, KVM could always do XRSTOR with XFD=0, e.g. by using
a constant XFD based on the set of enabled features when XSAVEing for
a struct fpu_guest. However, having XSTATE_BV[i]=1 for XFD-disabled
features can only happen in the above interrupt case, or in similar
scenarios involving preemption on preemptible kernels, because
fpu_swap_kvm_fpstate()'s call to save_fpregs_to_fpstate() saves the
outgoing FPU state with the current XFD; and that is (on all but the
first WRMSR to XFD) the guest XFD.
Therefore, XFD can only go out of sync with XSTATE_BV in the above
interrupt case, or in similar scenarios involving preemption on
preemptible kernels, and it we can consider it (de facto) part of KVM
ABI that KVM_GET_XSAVE returns XSTATE_BV[i]=0 for XFD-disabled features.
[Move clea
---truncated---
